Program 01: CO setting #1
The upper row display: LINE SETTING 1
The lower row display: L-ABCDE
L: 01--16(CO line port number or * for all CO lines)
A: 0-2 (CO line connection: 0-disable connection,1-enable but without CLID, 2-enable connection but with
CLID)
B: 0-3( Caller ID delay time: 0-3s,1-5s,2-10s,3-fine adjustment )
C: 0-1 (1--Auto-attendant mode,  0—Ring at appointed extension.)
D: 0-3( Auto Attendant: 0-disable 1-available Day mode only, 2-available Night mode only, 3- available Day/Night mode)
E: 0-1(Line restriction:0-restricted line, 1-unrestricted line)
Unrestricted line means that this outside is unrestricted when the extension use this line to dial any outside number; restricted line means some extension or some numbers are restricted from dialing through this outside line.
Program for single line phone:
Single Line Phone:
    Input program item code”01”, the program status entered when hear a long reminding tone. Firstly, input CO.LINE number 01-16 , then press” * ” for cursor shift to CO Line setting and input relative parameter.
After finish that, press” * ”,transfer to next CO Line setting, and repeat the above procedure. Press “#” to save and return to system program status.

(Default: The former 8 CO line—20000,the latter CO line—00000.
Ex: Set CO line 5 be day-mode auto-attendant
Key phone set: “CHECK” key 3 times-“1967590-01-5-“TRF”-10110-“HOLD”-
“CLEAR” 1 time.

Program 02: CO setting #2
The upper row display: LINE SETTING 2
The lower row display: L- ABCDE
L: 01-32(CO line port number or * for all CO lines)
A: 0-1(PBX line:0-No, 1-Yes)
B: Dialing out without dialing “9” or “3”.1-- Not dial “9”,0—Not dial “0”.
C: 0-1(Call release time: 0-1.5 seconds, 1-4 seconds)
D: 0-2 (Flash time: 0-300ms, 1-600ms,2-900ms)
E: Mode Of Charge Counting,0—Delay counting,1—Reverse charge counting.

Single Line Phone:
   Input program item code”02”, the program status entered when hear a long reminding tone. Firstly, input CO.LINE number 1-16 , then press” * ” for cursor shift to CO Line setting and input relative parameter.
After finish that, press” * ”,transfer to next CO Line setting, and repeat the above procedure. Press “#” to save and return to system program status.
(Default: All CO line port-00010)

Program 03: Abbreviation Code
The upper row display: ABBREVIATE CODE 
The lower row display: DC--

DC: series number, from 00—49,total 50 groups;
This system can set 50 groups
XXXX: Economical Code route number for the Telecom Carriers (max. 20- digit) ;

Single line phone
Input program item code 03, the program status entered when hear a long reminding tone. Firstly, input two-digit series number, then “ * “ plus the Economical Code route number. To delete the route number, press “ * “ under XXXX status. Press “#” returning to system program status.
Ex: Set “17900” at Abbreviation Code 3.
Key phone set: “CHECK” 3 times-1967590-03-03-“TRF”-917900-“HOLD”-“CLEAR” 2 times.
Single line set:#787-1967590-03-03-*917900-#.

(Default: NONE)

 

Program 04: System setting #1
The upper row display: SYSTEM SETTING 1
The lower row display: ABCDE

A: Day/night service mode,1—Auto;0---Operator
B: Trunk number integration mode,0--swift,1--slow
C: 1-4(Incoming call ringing time-delay: 1~4 is time of 1~4 rings)
D: 0-1(Outgoing call decoder release time: 0-25seconds, 1- 10seconds)
E: 0-1(Auto-attendance to enable/disable decoder. 0- disable, 1- enable)

Single line phone
Input program item code 04, then reminding tone is heard, that means entering into system program status. Then input relative parameter, after finish that, press“#”to return system program status.
REMARKS:
1. In this program if day/night transfer mode will be set to be auto transfer mode, it has something to do with the set of program 08.
2. In this program the set of incoming call ringing time-delay has something to do with that of program 13.
3. In this program the starting time has something to do with charge counting.

Program 05: System setting #2
The upper row display: SYSTEM SETTING 2
The Lower row display: ABCDE

A: 0-1 (If caller do not dial any number in Auto Attendance announcement, The call will transfer to Operator phone: 0-No (cut-off), 1-Yes )
B:0-1 (Should press “TFR” for One-touch Transfer method at key phone: 0- Need, 1- No need.)
C: Valid starting time of charge counting,0-at once,1—10 seconds later,2—30 seconds later,3—60 seconds later,
D: Trunk number integration swift mode :0—7 seconds,2 seconds best.
E: 0-1( Seek CO Line dialing out code.  There’s two groups, one is dial “9” to select CO Line, second is dial “3” to select CO Line: 0-only allow one group dialing out, 1-allow two groups)
The system has 8 rout out. If set several rout out, please dial 91—98 to choose rout out mode. The relative dialing-out CO line is set by program 38.
Single line phone
Input program item code 05, then reminding tone is heard, that means entering into system program status. Then input relative parameter, after finish that, press“#”to return system program status.
(Default: -01100)

 

 

Program 06: System setting #3
The upper row display: SYSTEM SETTING 3
The lower row display:-ABCDE

A: Choice of Counting charge software,1—normal counting charge software,,2—3S counting charge software,
B: Trunk number integration open mode,0—not open,1---open
C: 0-4(The duration to call-back the extension which holding a CO line: “0”-do not call-back,”1”- 30sec,”2”- 1 min., “3”- 1.5 min., “4”- 2 min.)
D: 0-1(Conversation alarm mode: “0”-alarm for both incoming & outgoing call, “1”-only alarm for outgoing call.)
E: With DSS.0—with, 1—without
DSS can be only connected to the Port 001 of Chinese key phone.

Single line phone
Input program item code “06”, then reminding tone is heard, that means entering into system program status. Then input relative parameter, after finish that, press“#”to return system program status.
(Default: -20200)

 

Program 07: System setting #4
The upper row display: SYSTEM SETTING 4
The lower row display:-ABCDE
A: Use full flexible numbering,0—close full flexible numbering,1—open  full flexible numbering
B: 0-1( Economical Code auto-route: 0-not allowed,1-allowed)
C: Choice of call reminding tone,0—the first,2—the second
D: Play time of the operator,0—45s,1—90s.
E: Charge counting,0—only long-distance call,1---all calls.

Single line phone
Input program item code 07, then reminding tone is heard, that means entering into system program status. Then input relative parameter, after finish that, press“#”to return system program status.
(Default: 00100)

Program 08: Night transfer
The upper row display：INTERNATIONAL FAVORABLE TIME
The low row display: XX:XX-YY:YY-ZZ
                   XX:XX:THE STARTING TIME
                   ZZ: FAVORABLE RATE
N: Series number 1-2 ( “1”-The delay-time to receive and display incoming number Caller ID, starting from the time on ringing signal detected  , “2”-The duration between dialing Economical Code route code leading number and dialing the actual PSTN number. )
XY: Duration , 00-99: from “0” to “99” seconds.

Single line phone
Input program item code 08, then reminding tone is heard, that means entering into system program status. Then input relative parameter, after finish that, press“#”to return system program status.
(Default: None)

Program 09- Outgoing call setting ( Day mode)
The upper row display: DAY LINE OUT SET
The low row display: ST –Y-XXXXXXXX
(Remarks: The authority for the extension to make outgoing calls in Day time mode )

ST: 001-128 (Extension port number,”***”represent all extensions)
Y: The number of the former 8 and the latter 8 CO lines.0—01-08 CO lines,1—09-16 CO lines.
XXXXXXXX:8 digitals, 0 or 1,(the extension to use the relevant CO Line: “0”-Not allow,”1” -Allow.)

Single line phone
  Input program item code “09”, then reminding tone is heard, that means entering into system program status. Then input the extension port number, press “ * ” jumping to extension port parameter setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
◆ Ex: Set port 008 can dial out only by CO line 5 and 6.

Key phone: press FNC key three times-1967590-09-”***”. Input program item code 09,display “001-1-11111111”.Then input Port NO. 008,press  “TRF” and input “00001100” and press “TRF” and display “008-2-11111111”.And then input “00000000” and press “Hold” 1 time “CLEAR” 2 times.

 

Program 10: Outgoing call setting ( Night mode)
The upper row display: NGT LINE OUT SET
The lower row display: ST-Y-XXXXXXXX
(Remarks: The authority for the extension to make outgoing calls in Night time mode )

ST: 001-128 (Extension port number,”***”represent all extensions)
Y: The number of the former 8 and the latter 8 CO lines.0—01-08 CO lines,1—09-16 CO lines.
XXXXXXXX: 8 digitals, 0 or 1,(the extension to use the relevant CO Line: “0”-Not allow,”1” -Allow.)

Single line phone
   Input program item code 10, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to extension port dialing-out parameter setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
(Default: Key phone: press FNC key three times-1967590. Input program item code 10,display “001-1-11111111”.Then input Port NO. 008,press “TRF” and input “00001100” and press “TRF” and display “008-2-11111111”.And then input “00000000” and press “Hold” 1 time “CLEAR” 2 times.
   Single line phone:
   Hook off and press “#787-19567590-10-008-*-00001100-*-00000000-#-hook on..
 

 

Program 11: Incoming call setting (Day mode)
The upper row display: DAY LINE IN SET
The lower row display: ST-Y-XXXXXXXX
(Remarks: During Operator status, the incoming calls will or will not ring to the desired extension in Day time mode )

ST: 001-128.(Extension port number,”***”represent all extensions)
Y: The number of the former 8 and the latter 8 CO lines.0—01-08 CO lines,1—09-16 CO lines.
XXXXXXXX: 8 digitals, 0 or 1,(the extension to use the relevant CO Line: “0”-Not allow,”1” -Allow.)
Single line phone
Input program item code “11”, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to extension for incoming call ringing parameter setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
◆ Ex: set CO Line 2 ringing at extension 8002 (port no.002)

Key phone: press FNC key three times-1967590-11-002-press TFR one time -00000010-press TFR one time, and then press “CLEAR” 2 times.
Single line phone: hook off- input # # 787-1967590-11-002-*-00000010 -# - hook on
(Default:
All CO lines call in, port 001 rings
Single line phone: hook off- # # 787-1967590-09-008-*-00001100-*00000000*-00000000*00000000-#  hook on.)

Program 12 : Incoming all setting ( Night mode)
The upper row display: NIGHT LINE IN SET
The lower row display: ST-Y-XXXXXXXX

ST: 001-128.(Extension port number,”***”represent all extensions)
Y: The number of the former 8 and the latter 8 CO lines.0—01-08 CO lines,1—09-16 CO lines.
XXXXXXXX: 8 digitals, 0 or 1,(the extension to use the relevant CO Line: “0”-Not allow,”1” -Allow.)
Single line phone
Input program item code “11”, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to extension for incoming call ringing parameter setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
◆ Ex: set CO Line 5 ringing at extension port no.002

Key phone: press FNC key three times-1967590, input program number “12”,display “001-1-11111111”.And then input port NO.001.
Press TRF 1 time and input “11110111”,and then press “TRF” 1 time ,display “002-1-00000000”.Then input “00001000”, press TRF 1 time, display “002-2-00000000”. And input “00000000”, press “HOLD” 1 time CLEAR 1 time.
Single line phone: hook off- input # # 787-1967590-11-001-*-11110111-*-11111111-*002-*-00001000*-00000000#-hook on..
(Default:
All CO lines call in, port 001 rings

Program13: Setting of delay ringing/DISA setting
The upper row display: LINE RING DELAY
The lower row display: ST-Y-XXXXXXXX

ST: 001-128.(Extension port number,”***”represent all extensions)
Y: The number of the former 8 and the latter 8 CO lines.0—01-08 CO lines,1—09-16 CO lines.
XXXXXXXX: 8 digitals, 0 or 1,(the extension to use the relevant CO Line: “0”-Not delay,”1” -Delay) 

Single line phone
 Input program item code 13, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to incoming call ringing-delay parameter setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
! Remark: The time of ringing delay is related with 03 of Program 04.
Default:
9D:
(001-252)-1-00000000(All the CO lines dialing in doesn’t have extension ringing time delay.)
(253—256)-1-11111111(All password can dial out through all CO lines.)
6D:
(001-192)-1-00000000(All the CO lines dialing in doesn’t have extension ringing time delay.)
         2-00000000
         3-00000000
         4-00000000
(253—256)-1-11111111(All password can dial out through all CO lines.)
          2-11111111
          3-11111111
          4-11111111

 

Program14：Serving class
The upper row display: SERVICE CLASS
The lower row display: ST-AB-X

ST: 001-128.(Extension port number,”***”represent all extensions)
A:  6-class of service
Class 1: No restriction ,free for any call.
Class 2: Do not allow to call internationally.
Class 3: Do not allow to call nationally or internationally, but open some assigned numbers for long-distance call.
Class 4: Do not allow for any long-distance call but available civic calls.
Class 5: Only available for emergency call and intercom call.
Class 6: Only intercom call allowed.
B:  The class of service after extension locked (6-class same as “A”).
X:  Reference for programmable key of the key phone.
Single line phone
Input program item code 14, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to class of service and class-after-locked setting. Press “ * ” again jumping to next extension setting, after finish that, press“#”to return system program status.
(Default: ST-14)

 

 Program 15: Restriction code A
The upper row display: RESTRICT CODE A
The lower row display: ST-XX
(To restrict the leading digit for international call, and special service call which maybe provided by local Telecom Carrier.)

ST: 01-04 (series number, total 4-group can set)
XX: Restrict code, max. 8 digits
This program is 4 groups of 1—8 restriction code, which can be set for domestic and international long-distance call or special code and is used for Level 2 and 4.
Single line phone
Input program item code 15, then reminding tone is heard, that means entering into system program status. Firstly input the group number, press “ * ” jumping to restricted code setting. Press “ * ” again jumping to next group setting. If do not input any restricted code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
(Default: 01-00, 02-168, 03-968, 04-969)

 Program 16: Restriction code B
The upper row display: RESTRICT CODE B
The lower row display: ST-
(To restrict the leading digit for national long-distance call, and special service call which maybe provided by local Telecom Carrier.)

ST: 01-20 (series number, total 20-group can set)
X: Restrict code, max. 8 digits
This program is 4 groups of 1—8 restriction code, which can be set for domestic and international long-distance call or special code and is used for Level 3 and 4.

Single line phone
Input program item code 16, then reminding tone is heard, that means entering into system program status. Firstly input the group number, press “ * ” jumping to restricted code setting. Press “ * ” again jumping to next group setting. If do not input any restricted code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
 (Default: 01-0, 02-168, 03-968, 04-969)
!  Remarks: The restriction code B is for Classes 3~6 stated in Program 14.
    “0” is for National long-distance call, “168””968””969” are service call in China.

 

 Program 17: Open code C
The upper row display: UNREST CODE C
The lower row display: ST-
(Still open the leading digit dialing-out even extension do not allow to dial long-distance call,)

ST:01-12(series number, total 12-group can set)
This program is 12 groups of open code,1—8 digits. It can set groups of call numbers restricted by Program 15 and 16.

Single line phone
Input program item code 17, then reminding tone is heard, that means entering into system program status. Firstly input the group number, press “ * ” jumping to open code setting. Press “ * ” again jumping to next group setting. If do not input any open code but press “ * ” will delete the present code and switch to next group setting. Press”#” to return system program status.

 

 Program 18: Public code D
The upper row display: Public CODE D
The lower row display: ST-XXX
(The extension free from no-outside call restriction and allow to dial emergency call )

ST: 01-04 (series number, total 4-group can set)
XXX: Public open code, max.8 digits.
The public code refer to some special numbers ,such as 110,119.
Single line phone
Input program item code 18, then reminding tone is heard, that means entering into system program status. Firstly input the group series number, press “ * ” jumping to open code setting. Press “ * ” again jumping to next group setting. If do not input any open code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
(Default: 01-110, 02-112, 03-119)
!  Remarks: The open code D is for Classes 1~5 stated in Program 14.
    “110,112,119” is for emergency call in China.

 

 Program 19: PBX – via - PBX Outgoing Code
The upper row display: PBX ACCESS CODE
The lower row display: ST-X
ST:01-04(series number, total 4-group can set)
X: PBX restricted code, max 1 to 2 digits.

Single line phone
Input program item code 19, then reminding tone is heard, that means entering into system program status. Firstly input the group series number, press “ * ” jumping to PBX restricted code setting. Press “ * ” again jumping to next group setting. If do not input any open code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
(Default: none)

 

 Program 20: Accompany Account code setting
The upper row display: ACCOMPANY CODE
The lower row display: ST-XXXXXXXX- X-Y
(Explain: set the password to open service class in any extension by the relevant authority allowed)

ST: 001-255 (Account series number, total 32-group accounts can set)
XXXXXX: Password of account code,6 digitals
X : Serving levels,1-6 (Class of service, total 6-class)
Y: Dialing-out right of the accompany code,1—4 kinds. Dialing out through which CO line will be assigned by Program 13 125--128.In order to make the people are convenient to use the telephone to dial the long-distance call and keep in touch with others. The call record will be kept on the accompany code not on the extension.10 seconds after you dial out by accompany code, other CO lines can be called.   
Single line phone
Input program item code “20”, then reminding tone is heard, that means entering into system program status. Firstly input the account series number, eg.001,  press “ * ” jumping to password setting, press “ * ” to class of service setting. Press “ * ” again jumping to next account group setting,eg.002 . If do not input any open code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
(Default: none  )

Program 21: DISA(Trunk to trunk transfer) access code setting
The upper row display: DISA access code
The lower row display: ST-XXXXXXXX- X-Y
X: Serving level;(1 to 6 levels)
Y: Dialing-out right of the accompany code,1—4 kinds. Dialing out through which CO line will be assigned by Program 13 125—128.In order to make the people are convenient to use the telephone to dial the long-distance call and keep in touch with others. The call record will be kept on the accompany code not on the extension.10 seconds after you dial out by accompany code, other CO lines can be called.   
Single line phone
Input program item code “21”, then reminding tone is heard, that means entering into system program status. Firstly input the account series number, press “ * ” jumping to password setting, press “ * ” to class of service setting. Press “ * ” again jumping to next account group setting,eg.002 . If do not input any open code but press “ * ” will delete the present code and switch to next group setting. Press“#”to return system program status.
(Default: none  )

 

 

 Program 22: Extension setting #1
The upper row display: EXT SETTING 1
The lower row display: ST-ABCDE

ST: 001-128.(Extension port number,”***”represent all extensions)
A:0-3 (Call waiting alert when busy: 0-intemal call alert OFF and external call OFF;1- internal call alert ON and external call OFF;
2-Internal call alert OFF and external call ON;3- Internal call alert ON and external call ON)
B: 0-1 (Caller ID: 0-off, 1-on)
C: 0-3 (Conversation duration alert:”0”-nil,“1”- 3min., “2”- 6min., “3”- 9min.)
D: 0-1 ( Call being interrupted and cut-off : 0-not allowed,1-allowed)
E: Choice of key phone,0—English,1—Chinese.

Single line phone
Input program item code 22, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to ABCDE setting, Press “ * ” again jumping to next extension setting. Press”#” to return system program status.
(Default: all extension - 31001 )

 

 Program 23: Extension setting #2
The upper row display: EXT SETTING 2
The lower row display: ST-ABCDE

ST: 001-128.(Extension port number,”***”represent all extensions)
A: 0-8 ( CO Line is automatically or randomly being selected when extension goes off-hook.  0- select any CO Line. 1~8: to firstly select assigned CO Line1~8. )
B: 0-2 (Do Not Disturb setting: “0”-DND disabled,”1”-DND for external call, “2”- DND for both external and intercom call.)
C: 0-1 (Comply to call via Economical Code auto-route, “0”-off, “1”-on .)
D: 0-1 (CO dial out setting: “0”- dialing out by “9” ,”1”-dialing out directly)
E: Extension call limit:0—enable,1--disable

Single line phone
Input program item code 23, then reminding tone is heard, that means entering into system program status. Firstly input the extension port number, press “ * ” jumping to ABCDE setting, Press “ * ” again jumping to next extension setting. Press”#” to return to system program status.
(Default: All extensions-02000)

Program 24: Pickup Group Assignment
The upper row display: PICKUP GROUP
The lower row display: X-ST-A
(Explain: to allow or restrict the extension to pick up the ringing call within the group.)

X:  1—4 (pickup group number)
A：Join in/opt out.(1—Join in,0—Opt out)

Single line phone
Input program code 24, then reminding tone is heard, that means entering into system program status. Firstly input the pickup group series number, press “ * ” jumping to extension number setting, Press  “ * ” to set pickup authority. Press “ * ” again jumping to next extension pickup authority setting.  Press”#” to return to system program status.
(Default: All extensions are in the same pickup group)

 Program 25: Manager/secretary Call Group
The upper row display: EXEC/SEC PAIR
The lower row display: X-EX-SE
(Secretary pick up the incoming call instead of manager. System can set 8-group manager secretary call group)

X: 1-8 (number Manager/secretary call group, max. 8-group)
EX:001--128.(Extension port number of the EX,”***”represent all extensions)
SE: 001--128.(Extension port number,”***”represent all extensions)
After active this function, calls to Boss will automatically route to Secretary and then transfer the calls to Boss by Secretary.

Single line phone
Input program item code “25”, then reminding tone is heard, that means entering into system program status. Firstly input the manager/secretary group series number, press “ * ” jumping to manager extension number setting, Press  “ * ” to set secretary extension number setting. Press “ * ” again jumping to next manager/secretary call group setting.  Press”#” to return system program status.
(Default: none)
!  Remarks: This program is available before enabling Do Not Disturb function in manager extension.

 Program 26: System Program Password
The upper row display: SYS SECRET CODE
The lower row display: XXXXXXX
(To check or change the system program password)

Single line phone
Input item code 26,then reminding tone is heard, that means entering program status. Then input 7-digit new password. Press “#” to return system program status..
(Default password: 1967590 ,total 7-digit )
!  Remarks: Should use new password to enter into system program if the password changed . Keep the new password carefully.

 

 Program 27 : Setting Operators
The upper row display: SPECIAL PORT
The lower row display: DISA PORT
DISA PORT: Trunk to Trunk extension port
Console 1: ST
Console 2:(not set)
Console 3: (not set)
ST: 001-128.(Extension port number,”***”represent all extensions)

Single line phone
Input item code “27”, then reminding tone is heard, that means entering into system program status. Single line phone set can only set one operator in the system. After finish, press “# “ returning to system program status.
(Default: CONSOLE1: 001 )

 

 Program 28: Re-set System
The upper row display: SYSTEM RESET
The lower row display: 1/2/0
(To set system to the factory default setting, including the system program password. )

  1/2- to reset( warning :all revised data will be lost),
0-do not re-set

Single line phone
Hook off and press “7871967590”.Input 28 and then input 1 to reset after you hear reminding tone.

 

 Program 29: Flexible Extension Numbering
The upper row display: PORT EXT NUMBER
The lower row display: ST-XXXX
(To change the old extension number to a desired new one)

ST:  001-128.(Extension port number,”***”represent all extensions)
XXXX:  It is the desired extension number from 2 to 4-digit number. The leading digit for the desired new extension number must be “1”, “2” or “8”.
!  Remarks:
i. Allowed number like “11,22,88, 100,288,800,1111,2999 or 8008” etc.
ii. Extension number can’t be repeated in same system.
iii. Clear all previous extension numbers: Input “ *** ”, press “TRF” twice.
iv. Clear the present extension number: Input extension number + “TRF + CLEAR + TRF or HOLD”.

Single line phone
Input item code 29, then reminding tone heard, which means entering into program status. Input old extension port number, press“ * “ and the new extension number (2 to 4 digits, leading “1,2,8”).
Press “*” again to set next new extension number.
Press “#”  returning to program status.
In the status of inputting extension number, if do not input but press “*”, the old number will be deleted.
Delete all previous numbers : at program 29, input “ * * * * * ”.
Process Of Clear All The Extensions
1. The digit of the extension number must be from 2 to 4.The starting digit number must be 1,2.or 8.
2. Before resetting the extension number, please clear all the number set before.
3. Not all of the extension number are at non-flexible numbering status.
(Default:  001-8001, 002-8002, … , 015-8015, 016-8080 )

 Program 30:  Unit Price Setting Of International Distance Call                                
The upper row display: INTERNATIONAL CALL UNIT PRICE
The lower row display: 00852-00:20-1
00852 is the country code of international distance call. First 00 is fixed value.
00:20 is the corresponding price for every 6 seconds of the present country.0—not open,1—open.
There are 250 international distance country code,214 of which is set before being
took out of the factory. The other 86 can be set at your own choice.

Program 31:  Unit Price Setting Of Domestic Distance Call    
The upper row display: INTERNATIONAL LONG-DISTANCE CALL UNIT PRICE
The lower row display: 0-00:00-1
(Default: The unit price of all the domestic long-distance call is 7 cents every 6 seconds.)
If you need to modify the unit price, you can add the code after 0 and change 00:00 into the unit price you want.
00:00 is the corresponding unit price of 6 seconds of the code.1 refers to open the IP phone function;0—not open.
Single line phone: Invalid
Key Phone:0-00:00-1

Program 32:  Unit Price Setting Of local Call
The upper row display: unit price of local call
The lower row display:1—00:14/1minute
Single line phone: Invalid
Key phone: All number-00:14/minute

 Program 33:  Call Charge Display
The upper row display: CALL CHARGE DISPLAY
The lower row display: Port 001
001:Port number, 4 input modes:
Assigned port number:001-128
Accompany password number:*001--*255
DISA password number:*#1-*#8
Assigned CO line number:#1--#8
Input the number of extension port or password, and press ”HOLD” key. Display the charge of all the time.
Input the number of extension port or password, and press” TRF” key to display the starting time first. The starting time can be modified and then press “TRF” key to display the charge of definite time.
Single line phone: Invalid

Program 34: Reviewing password of extension lock
( For feature phone only)
The upper row display: password
The lower row display: XXX
XXX: Extension port number, password is behind "-".
Enter station port number 001--128, and then press TRF key to shows the password at upper row.

Program 35: Review system charge counting
( For feature phone only)
The upper row display: CHARGE COUNTING
The lower row display: -XXXX
XXXX: indicates the stored number of charge counting of system.
The max total storage is 400.

Program 36: Preset call charges
The upper row display: LEFT CHARGE DISP
The lower row display: PORT ST
ST: Port number,3 input modes:
Assigned port number: 001-128
Accompany password number:*001--*255
DISA password number:*#1-*#8
Input the number of extension port or password, and press HOLD or TRF key. Enter the input of the preset charge.
Input preset charge from 0000.00 Yen to 9999.99 Yen, and press HOLD key to reserve. If you want to cancel the function of certain port or password, please press CLEAR key in the preset charge status and press HOLD key to reserve.
Single line phone: Invalid
 

(责任编辑：admin)

上一篇：WS824(5D)&WS824(8D)manual
下一篇：国威WS824（5D）型数字集团电话系统